Faucet repair and installation, Phoenixville PA
Faucet Repair & Installation in Phoenixville, PA
A drip that will not quit, a handle that spins loose, a new faucet that will not seat on an old sink. Small jobs, but the shutoffs under a hundred-year-old sink rarely cooperate.
- Licensed and insured.
- Answered around the clock.
- Straight to a plumber, no forms.
The reality.
Why a simple faucet swap is rarely simple here.
On paper a faucet is a fifteen-minute job. In a Phoenixville rowhome it often is not, and the reason is everything around the faucet rather than the faucet itself. The angle stops under the sink may be original, seized and prone to weep the moment they are turned. The supply risers may be old chrome or galvanized. The countertop hole spacing on a vintage sink may not match a modern fixture. None of that is a crisis, but it is why a quick swap sometimes turns into replacing the shutoffs too, and it is better to know that going in.
A dripping faucet, meanwhile, is not just an annoyance. A steady drip wastes a surprising amount of water over a year and, on the hot side, energy with it. Most drips are a worn cartridge, washer or O-ring and are a genuine quick fix once the fixture is apart.
The choice.
Repair or replace, honestly.
Whether to repair or replace comes down to the faucet. A decent fixture with a worn internal part is worth repairing; a corroded, bottom-of-the-range faucet that leaks from the base is usually better replaced than nursed. We will tell you which yours is rather than defaulting to the more expensive answer, and if a repair buys you a good while, that is what we will do.
When you are installing new, we check the shutoffs and supply lines while we are under there, because a fresh faucet on failing angle stops is a call-back waiting to happen. Doing both at once is the difference between a fix and a temporary one.
Faucet problems we handle.
- Constant drips from the spout or handle base.
- Low or uneven flow from a single fixture.
- Loose, stiff or leaking handles and cartridges.
- New kitchen, bath and utility faucet installation.
- Old, seized shutoff valves replaced at the same time.
Drip keeping you up at night?
Call and describe the faucet and the sink.
What wears out.
The parts that fail, and why quality matters.
When a faucet is repaired rather than replaced, it helps to know what actually wears out. Inside most faucets the moving seal is a cartridge, a ceramic disc, or a set of washers and O-rings, and it is almost always one of those, not the faucet body, that causes a drip. A cartridge is an inexpensive part, and a good-quality faucet has cartridges still available years later, which is a large part of why a decent fixture is worth repairing while a bottom-of-the-range one often is not.
The cheapest faucets tend to use proprietary or hard-to-source parts and thin bodies that corrode, so nursing one along costs more over time than replacing it with something serviceable. When we do install new, we are glad to point you toward fixtures whose parts you will still be able to buy in a decade, because a faucet is not a place where the cheapest option is the economical one. It is a small fitting, but the difference between a repairable one and a disposable one shows up every time it needs attention.
Questions
Faucet questions.
Worth fixing. Beyond the annoyance, a steady drip wastes a meaningful amount of water over a year, and on the hot side it wastes energy too. Most drips are a worn cartridge, washer or O-ring, which is an inexpensive repair once the fixture is apart, so there is rarely a reason to live with it.
Because of what is around the faucet in an older house. The shutoff valves under the sink are often original and can seize or weep when turned, the supply risers may be aged, and a vintage sink's hole spacing may not match a modern fixture. None of it is major, but it sometimes means replacing the shutoffs at the same time, which we would flag before starting.
Yes. We are happy to fit a fixture you have chosen, and we will check the shutoffs and supply lines while we are under the sink so the new faucet is not sitting on failing valves. If the sink and faucet are not a match, we will tell you before drilling anything.
Kitchen, bathroom, and utility and laundry faucets. If it drips, sticks, leaks or needs installing, it is the same visit.